Fiat Punto 2004 Training Manual Download Page 438

Page: 438 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Cruise Control control lever

This system is managed by the engine control unit and makes it possible to easily maintain the

set vehicle speed, regardless of the varying running conditions.

Steering column stalk functions

Flashing light/steady high-beam headlamp switch:

the flashing light control is obtained by

pulling the lever from the rest position towards the steering wheel crown while preventing the

lever from going past the first click (“flashing light” contact). This actuation in UNSTABLE;

therefore, the lever shall return to its rest position when it is released, thus opening the

“flashing light” contact again.

The “steady high-beam headlamp” control is obtained by pulling the lever the same way as the

flashing light control; in this case, however, the lever shall be allowed to travel a longer stroke, up to

the second click (“high-beam headlamps” contact). Here too, the actuation is UNSTABLE: the lever

shall return to its rest position, thus opening the “high-beam headlamp” and “flashing light” contacts.

The high-beam headlamps can be turned off by pulling the lever again up to the high-beam

headlamp position, the same way as during ignition.

gb Fiat Grande Punto OK

437 / 532

Indicator and lane change light control:

this control is obtained by making the lever to move

along the steering wheel plane in both directions (upwards and downwards). The translatory

motion of the lever in each direction of rotation involves two different ways to actuate the

electric contact itself: an UNSTABLE one (referred to “lane change”) and a STABLE one

(referred to as “direction change”). The “lane change” function is actuated through a smaller

angular travel than the one required to actuate the “direction change”.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands