Fiat Punto 2004 Training Manual Download Page 469

Page: 469 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

– press the

MENU ESC

button again for a long time to go back to the standard screen or the

main menu, depending on the menu point reached.

Deadlock device

This is a safety device (where available) that disables the operation of the following items:

inner handles;

locking/unlocking button;

gb Fiat Grande Punto OK

468 / 532

thus preventing the doors from being opened from inside the passenger compartment in the

event that an attempt at breaking into the vehicle has been made (e.g. glass breaking).

Therefore, the deadlock ensure the best protection against any attempt at theft. It is

recommended that the system is actuated every time the vehicle is left parked.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 469 / 533

Search results

Summary of Contents for Punto 2004

Reviews: