Fiat Punto 2004 Training Manual Download Page 483

Page: 483 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Headlamps

The newly-designed transparent glass front light clusters contain the bulbs for dimmers

(W 5

W bulb), low-beam/high-beam headlights

(H4 55/60 W bulb) and indicator lights

(PY 21 W

bulb). Headlamp trim is controlled by electric motors.

Lamp replacement:

the low-beam/high-beam headlight and dimmer bulbs can be replaced by

removing the rubber cap

force-fitted at the light cluster rear. Release H4 bulb

and take it

out. As regards dimmer W5W bulbs

, take it out of seat

(without taking the light cluster off

the vehicle). The light indicator bulbs can be removed by steering the front right or left wheels

outwards to gain access to the lid on the wheelbox, which will be released by turning the

locking device counterclockwise. Now, the bulb holder cover can be removed by being rotated

counterclockwise.

gb Fiat Grande Punto OK

482 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 483 / 533

Search results

Summary of Contents for Punto 2004

Reviews: