Fiat Punto 2004 Training Manual Download Page 436

Page: 436 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

General remarks

Light control lever

Below are the controls associated with this lever:

light selector;

flashing light/steady high-beam headlamp switch;

indicator and lane change lights.

The controls are actuated by acting on the levers as follows:

movement on the steering wheel plane in both directions, with double click (the former is

unstable, the latter is stable);

pulling movement towards the driver, with double click (unstable);

ring rotation by 3 or 4 clicks.

gb Fiat Grande Punto OK

435 / 532

LIGHT LEVER

WIPER LEVER

CRUISE CONTROL

LEVER

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands