Fiat Punto 2004 Training Manual Download Page 431

Page: 431 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Warning cycle

: signalling by means of the warning light and the acoustic signal.

The warning light on the board starts blinking, and the acoustic signal sounds intermittently for

90 seconds if any of the following conditions occurs:

elapsed time of 60 sec and vehicle speed higher than 10 k.p.h.;

vehicle speed higher than 25 k.p.h.;

covered distance longer than 500 m.

If the belts are fastened during the cycle, the warning cycle will be automatically interrupted

and will be repeated only when the unfastened belt condition occurs again.

Warning cycle switch-off mode

: the driver may switch the warning cycle off temporarily

before the key-ON (by fastening the front safety belt(s), by keeping the same for at least 20

seconds with the key ON and then releasing it) or permanently, by asking for the assistance of

the Technical Service personnel. The warning cycle is actuated again upon every key-ON

(with the temporary switch-off mode).

Warning cycle re-actuation mode

: the driver may actuate the warning cycle again (it the

latter has been switched off permanently) by either asking for the assistance of the Technical

Service personnel (Mode panel) or through a special item of the set-up menu (Comfort and

Matrix panels). This item will disappear when the warning cycle is actuated again.

External temperature displaying

Available with the Comfort and Matrix panels.

The external temperature indication is ensured, if the external temperature sensor is available,

in standard screen conditions.

The desired unit of measurement (°C or °F) can be selected from the set-up menu.

Warning/danger signalling: “Ice”

Available with the Comfort and Matrix panels.

In order to warn the driver that icy patches may be found on the road surface, when the

measured external temperature is equal to or less than 3°C, the Comfort panel display shows

the warning message:

gb Fiat Grande Punto OK

430 / 532

the blinking external temperature (for the duration of the message);

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands