Fiat Punto 2004 Training Manual Download Page 495

Page: 495 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Blaupunkt CD- changer (10-disc) features:

•

power-driven eject loading;

•

CD and track selection (UP & DOWN);

•

pause;

•

FF/F-REW;

•

“Scan” function;

•

“Track Repeat” and “CD Repeat” functions;

•

“Mix” (CD–magazine) function;

•

TPM (Track Program Memory) function;

•

CD Naming (8 characters for 30 CDs).

Telephone section features:

•

telephone mute ON/OFF function;

•

telephone volume function (telephone volume control through the volume knob).

Steering wheel radio controls.

The car radio system features remote controls on the steering wheel (see figures below).

gb Fiat Grande Punto OK

494 / 532

List UP/DOWN scrolling

Actuates MUTE voice/radi

ESC

Radio volume c/–

Radio sound source se

SRC

arch

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands