Fiat Punto 2004 Training Manual Download Page 78

Page: 78 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

The distributing shaft (on the exhaust side) is directly driven by the chain and transmits the

motion to the distributing shaft (on the intake side) by means of a pair or straight-toothed

gears.

The distributing shaft on the exhaust side also drives the high-pressure pump, whereas the

one on the intake side drives the vacuum pump.

3.2.14 Tappets

A hydraulic tappet is used for every single valve, which is actuated by a rocker arm that is, in

turn, driven by the cam axle.

The rocker arms are made in such a way as to avoid serious damage to the other engine

members in case of timing chain breaking or stepping. In fact, they are able, thanks to a pre-

established fracture section, to get deformed so as to absorb the stress caused by the contact

between the valves and the pistons.

FIAT PUNTO

78 / 532

Intake-exhaust valve diameter: 21.47 mm

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands