Fiat Punto 2004 Training Manual Download Page 412

Page: 412 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Speedometer

The instrument board provides a speed reading slightly higher than the actual speed, due to

safety reasons. This increase is calculated by the panel. Upon key-ON, the indicator reaches

0 (zero) k.p.h. (or m.p.h.) and the instrument board displays the vehicle speed information.

Revs counter

Upon key-ON, the indicator reaches 0 (zero) r.p.m. and the instrument board displays the

engine revs information. Moreover, a revs counter anti-oscillation logic is available in the

engine idle running conditions.

- in the temperature is included between 80° and 15°C (

normal operation

), the pointer will

remain stable in the middle of the scale;

Fuel level indicator

Two seconds after the key-ON, the indicator displays the fuel level information.

The indication corresponding to the start of the “fuel reserve” is red, and the relevant warning

light is made of an amber LED (positioned among the indicator’s graphic elements). The

indicator calibration ensures greatest accuracy at the start of the red sector.

Engine coolant temperature indicator

Two seconds after the key-ON, the indicator displays the engine coolant temperature

information.

The indication corresponding to the start of the “hazard area” is red, and the relevant warning

light is made of a red LED (positioned among the indicator’s graphic elements). The indicator

calibration ensures greatest accuracy at the start of the red sector.

Pointer behaviour:

- if the temperature is

≤

50°C, the pointer will position itself on the first mark/grade of the scale;

- if the temperature is included between 50°C and 80°C, the pointer will move linearly;

gb Fiat Grande Punto OK

411 / 532

- if the temperature is included between 115° and 124°C (uphill) and between 120° and 115°C

(downhill), the pointer will move linearly.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 412 / 533

Search results

Summary of Contents for Punto 2004

Reviews: