Fiat Punto 2004 Training Manual Download Page 519

Page: 519 / 533

AIR CONDITIONER

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Sectional view of the compressor

Technical features

The 5SL 12 compressor flow rate may vary depending on the load variations requested from

the system, as well as changing external temperature and/or humidity conditions, and sudden

engine load changes.

Below are the main technical features of the compressor:

direction of rotation: clockwise;

max. number of continuous revs: 8,500

number of pistons: 5

minimum displacement: 0 cm

/rev

maximum displacement: 126 cm

/rev

gb Fiat Grande Punto OK

518 / 532

amount of lubricant: 80 cm

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands