Fiat Punto 2004 Training Manual Download Page 121

Page: 121 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.6.6 Fuel tank and components

Submergible pump assembly (complete with level gauge control)

The fuel electric pump is fitted into one single assembly into the level gauge and the fuel filter;

therefore, the components cannot be replaced as individual items.

The function of the fuel electric pump is to feed the high-pressure pump. It is fully immersed

into the fuel inside the tank. The pump unit is realized so as to obtain the maximum fuel level

in the suction area.

This function is implemented by means of a Venturi pipe placed on the suction return pipe with

respect to the one of the tank. The pumping unit is of the roller type and makes it possible to

achieve a flow rate of 160 litres/h.

FIAT PUNTO

121 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands