manualshive.com logo in svg

Mopar 2005-2009 Chrysler 300C, Installation Instructions Manual, Page: 1 / 7

Share
Download
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual Download Page 1

          

 

 

Audio System Upgrade Package  

                                  2005-2009 Chrysler 300C 

 

Installation 

Instructions 

        

 

 

   

 

 

 

 

 

 

 

 

 

 

   

 

                                                 

 

 

 

 

77KICK02 

9/22/2008 

Page 1 of 7 

© 2007, Chrysler, LLC. Mopar is a registered trademark of Chrysler, LLC. All rights reserved. 

TOOLS REQUIRED: 

 

*Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife 

*Panel Removal Tool *10mm Wrench 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

CONTENTS: 

 

1EA.   SUBWOOFER ASSEMBLY 

P/N 05290522AB 

1EA.    100 WATT AMP ASSEMBLY 

P/N 05290521AA 

1EA. 

 

WIRE 

HARNESS 

  P/N 

RBI05300CSUB 

1EA. 

 

M6 

BOLT 

   P/N 

RFM6 

1EA. 

 

BODY 

CLIP 

   P/N 

06508613AA 

1EA. 

 

INSTRUCTIONS 

  P/N 

RBI05MAGSUB 

6EA. 

 

WIRE 

TIES 

   P/N 

RFZIP6 

4EA.   #8 SHEET METAL SCREWS 

P/N RFS2 

 
 

Summary of Contents for 2005-2009 Chrysler 300C








Reviews:

No comments