manualshive.com logo in svg

Mopar 2005-2009 Chrysler 300C, Installation Instructions Manual, Page: 4 / 7

Share
Download
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual Download Page 4

          

 

 

Audio System Upgrade Package  

                                  2005-2009 Chrysler 300C 

 

Installation 

Instructions 

        

 

 

   

 

 

 

 

 

 

 

 

 

 

   

 

                                                 

 

 

 

 

77KICK02 

9/22/2008 

Page 4 of 7 

© 2007, Chrysler, LLC. Mopar is a registered trademark of Chrysler, LLC. All rights reserved. 

 

12.

 

Plug the six pin connector of the wire harness into the amplifier. Fig. 9 

13.

 

Remove the plastic retainer securing the right side of the trunk liner to the floor to allow for wire 
routing. Fig. 10 

 
 
 
 
 
 
 
 
 
 
 

Fig. 9 

Fig. 10 

 
 
 

14.

 

Route the power and ground portion of the wire harness down the right side of the rear seat pass 
through and toward the battery along side the factory wiring using the supplied wire ties where 
needed. Fig. 11 

15.

 

Secure the harness with the factory retaining bracket. Fig. 12 

 
 
 

Fig. 11 

Fig. 12 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 2005-2009 Chrysler 300C








Reviews:

No comments