manualshive.com logo in svg

Mopar 2005-2009 Chrysler 300C, Installation Instructions Manual, Page: 6 / 7

Share
Download
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual Download Page 6

          

 

 

Audio System Upgrade Package  

                                  2005-2009 Chrysler 300C 

 

Installation 

Instructions 

        

 

 

   

 

 

 

 

 

 

 

 

 

 

   

 

                                                 

 

 

 

 

77KICK02 

9/22/2008 

Page 6 of 7 

© 2007, Chrysler, LLC. Mopar is a registered trademark of Chrysler, LLC. All rights reserved. 

 

20.

 

You will need to remove the plastic fastener in order to correctly position the wire harness.  It is not 
necessary to reinstall this fastener. Fig. 17 

21.

 

Route the speaker output portion of the harness toward the left rear fender well and back to the 
subwoofer mounting location.  The wire harness needs to route low enough that it will not be 
pinched by the subwoofer mounting bracket. Fig. 18 

 
 

Fig. 17 

 
 
 
 
 
 
 
 
 

Fig. 18 

 
 
 

22.

 

Install the speed clip that is provided onto the sheet metal just behind the left rear fender well.  

      Fig. 19 
23.

 

Remove the bag from the subwoofer assembly and lay it in the corner of the trunk where the 
subwoofer assembly will be placed.  The purpose of the bag is to prevent the Velcro

®

 mounting 

system on the bottom of the subwoofer assembly from engaging the carpet prematurely. Fig. 20 

 
 
 
 
 
 
 
 
 
 
 
 

Fig. 19 

Fig. 20 

 
 
 
 
 

Summary of Contents for 2005-2009 Chrysler 300C








Reviews:

No comments