Fiat Punto 2004 Training Manual Download Page 22

Page: 22 / 533

BRIEFING

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

1.2.9 Tyres and wheels

To optimize the vehicle performance, especially with regard to road holding, safety and driving

comfort, the following tyres have been fitted to Nuova Punto:

175/65 R15 -- Active / Dynamic

185/65 R15 – Active (option) / Dynamic (option) / Elegance / Sport (option – tyres can be fitted

with snow chains)

195/55 R16 -- Dynamic (option) / Elegance (option)

205/45 R17 -- Elegance (option) / Sport.

As far as alloy rims are concerned, Nuova Punto comes with a full range that stands out for

style, dimensions and paint colours:

FIAT PUNTO

22 / 532

ALLOY RIMS

5 dual rungs

colour:

silver standard

ALLOY RIM

10 rungs (of which, 5 dual rungs)

colour:

aluminium

ALLOY RIM

195/55/R16 tyres

14 rungs (thick/thin)

colour:

aluminium

ALLOY RIM

195/55/R16 tyres

18 triangular-section rungs

colour:

aluminium

ALLOY RIM

NON-CATENABILE
205/45/R17 tyres

15 flat-surface rungs

colour:

silver standard

ALLOY RIM

NON-CATENABILE
205/45/R17 tyres

15 flat-surface rungs

colour:

chrome shadow

ALLOY RIM

NON-CATENABILE
205/45/R17 tyres

3 dual rungs (spider-type)

colour:

chrome shadow

16"

17"

15"

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands