Fiat Punto 2004 Training Manual Download Page 9

Page: 9 / 533

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

8.3.2

Characteristic angles......................................................................................................................................... 374

ELECTRIC SYSTEM ................................................................................................................................................... 376

9.1

ENERAL DESCRIPTION OF THE SYSTEM

.................................................................................................................. 376

9.1.1

General features ................................................................................................................................................ 377

9.1.2

Serial lines and networks................................................................................................................................... 378

9.1.3

Network architecture ......................................................................................................................................... 380

9.1.4

Diagnosis instrument adapter............................................................................................................................ 383

9.1.5

B-CAN low-speed line........................................................................................................................................ 384

9.1.6

C-CAN high-speed line ...................................................................................................................................... 386

9.1.7

Remote-control switch/Fuse holder unit ............................................................................................................ 390

9.1.8

Wiring ................................................................................................................................................................ 393

9.1.9

Electronic components....................................................................................................................................... 396

9.2

ESCRIPTION OF COMPONENTS

................................................................................................................................ 398

9.2.1

Engine compartment control unit (FDU)........................................................................................................... 398

9.2.2

Luggage compartment node............................................................................................................................... 399

9.2.3

Body Computer node (BCM) ............................................................................................................................. 400

9.2.4

Instrument board node (IPC)............................................................................................................................. 409

9.2.5

Steering column stalk control module (CSM) .................................................................................................... 433

9.2.6

Radio receiver node (RRM) ............................................................................................................................... 447

9.2.7

Rear parking sensor node (PAM) ...................................................................................................................... 448

9.2.8

External audio amplifier for the hi-fi system ..................................................................................................... 453

9.2.9

Spiral cable........................................................................................................................................................ 453

9.2.10

Rain sensor control unit (RLS)...................................................................................................................... 454

9.2.11

Brake pedal switch ........................................................................................................................................ 454

9.2.12

Control board on the driver’s side front door (DDC)................................................................................... 455

9.2.13

Switch on clutch pedal .................................................................................................................................. 457

9.2.14

Central control board (CSS) ......................................................................................................................... 457

9.2.15

Left control board (ELC) .............................................................................................................................. 458

9.2.16

TPMS tyre pressure control system............................................................................................................... 459

9.3

ENTRAL LOCKING

.................................................................................................................................................. 460

9.3.1

General remarks ................................................................................................................................................ 460

9.3.1

System functions................................................................................................................................................. 464

9.4

LECTRIC WINDOW REGULATORS

............................................................................................................................ 472

9.4.1

General remarks ................................................................................................................................................ 472

9.5

XTERNAL LIGHTING

............................................................................................................................................... 479

FIAT PUNTO

9 / 532

9.6

UDIO SYSTEM

........................................................................................................................................................ 489

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 9 / 533

Search results

Summary of Contents for Punto 2004

Reviews: