Fiat Punto 2004 Training Manual Download Page 525

Page: 525 / 533

AIR CONDITIONER

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

15) AUTO DX button for automatic control of right-hand temperature, right-hand air

distribution, fan, compressor and air recirculation;

16) passenger’s side temperature selection knob.

The system makes it possible to adapt the passenger compartment air temperature (in the

driver’s side and passenger’s side parts) to the temperature requested in automatic mode. The

air flow rate, air distribution, compressor deactivation, recirculation state and the MAX DEF

function (which turns the rear heated window on automatically) can be selected manually.

Moreover, the system can, by means of the MONO button, be set to operate in a single-zone

mode, i.e. the air temperature and distribution in the passenger compartment, as requested by

the passenger, can be adapted to the one requested by the driver.

The operation logic is based on the equivalent temperature.

10.4 Diagnosis

Control unit proxy procedure

The control unit is capable, by means of special sensor control logic and setting logic with

actuator “self-learning”, to record and store in the memory a number of anomalies and faults

that may affect the system.

These stored errors can be read by getting connected to the Body Computer diagnosis

connector.

This operation makes the system learn the end-of-travel position of the air-conditioning control

unit electric actuators.

The established procedure can be carried out by means of the computer-assisted diagnosis

equipment.

This operation shall be repeated after at least one actuator has been replaced.

The procedure shall be started again in case of interruption.

gb Fiat Grande Punto OK

524 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands