Fiat Punto 2004 Training Manual Download Page 322

Page: 322 / 533

8-VALVE 1.4

ENGINE

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Tighten the tappet cover screws previously drawn nearer to the specified torque (0.8 ÷ 1.0

daNm).

Remove the tappet cover centring tool previously fitted.

Fit the phase sensor.

Fit the injection control unit support.

gb Fiat Grande Punto OK

322 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands