Fiat Punto 2004 Training Manual Download Page 363

Page: 363 / 533

ELECTRIC

DRIVE

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

“City” button

The “City” program maximizes comfort during the parking manoeuvres, with record-breaking

effort on the steering wheel (2.5 Nm compared with 4-6 Nm of traditional power steering

systems). The “Normal” program ensures average performance during the parking

manoeuvres while ensuring a gradual, optimum effort on the steering wheel even at low

speeds, especially in poor road grip conditions. In any case, both programs provide varying

interlocking depending on the vehicle speed (gradual power-assistance), therefore with no

compromise between the performance during the parking manoeuvres and the steering

control quality when the vehicle is running.

A special calibration for both programs is provided for every single body/engine versions.

gb Fiat Grande Punto OK

363 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands