Fiat Punto 2004 Training Manual Download Page 459

Page: 459 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

ASR deactivation and its respective optical indicator (LED on the button);

door locking/unlocking and its respective LED (the LED signals the door locking status when

the button is pressed and is lit continuously; moreover, it lights up intermittently to serve as a

deterrent when the vehicle is locked from the outside);

boot opening;

“Hazard” button for emergency light blinking;

“ECO” button to select the “Economy” mode (versions equipped with robotized gearbox).

9.2.15 Left control board (ELC)

The left control board (ELC) consists of a module that incorporates the controls on the steering

wheel outer side and is interfaced to the Body Computer node (BCM) and the instrument

panel node (IPC) through the dashboard cable harness.

The left control board (ELC) receives the power supply for ideograph lighting and includes the

following controls:

fog lights;

rear fog lights;

headlamp trim corrector;

mode:

mode +/ mode – control (used to control different functions depending on the instrument).

gb Fiat Grande Punto OK

458 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 459 / 533

Search results

Summary of Contents for Punto 2004

Reviews: