Fiat Punto 2004 Training Manual Download Page 461

Page: 461 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

9.3 Central locking

9.3.1

They are accompanied by the CODE Card.

General remarks

The keys are supplied in duplicate together with the vehicle.

electronic code;

mechanic code of the key, to be notified to the FIAT Dealership if a key duplicate is

requested.

It is recommended that you always bring the electronic code with yourself.

WARNING! To ensure optimum efficiency of the electronic devices fitted inside the key, the

latter should not be exposed to the sunshine.

gb Fiat Grande Punto OK

460 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands