Fiat Punto 2004 Training Manual Download Page 420

Page: 420 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Initial setting – Instrument initialization

The table below shows the factory-made instrument settings for the vehicle.

gb Fiat Grande Punto OK

419 / 532

COMFORT/MATRIX PANELS

MODE PANEL

Feature Available

Automatic

Available

Automatic

Speed limit (ON/OFF)

YES OFF

Speed limit

(threshold)

YES 130

k.p.h.

YES 130

k.p.h.

Twilight sensor

sensitivity (1…3)

YES 2

Trip B (ON/OFF)

YES ON

Clock setting

(hh/mm)

YES 0:00

Time format (12/24 h)

YES 24

Date setting

(dd/mm/yyyy)

YES

01/01/aaaa

yyyy: year of release

Audio information

repeat (ON/OFF)

YES ON

Door/boot locking

with speed > 20 k.p.h.

(ON/OFF)

YES OFF

Distance unit of

measurement

(km/miles)

YES

km if the

speedometer scale is

represented by the

kilometre; mi if the

speedometer scale is

represented by the

mile

YES

km if the

speedometer scale is

represented by the

kilometre; mi if the

speedometer scale is

represented by the

mile

Consumption unit of

measurement

(k.p.l., l/100 km,

m.p.g.)

YES

l/100 km if the

speedometer scale is

represented by the

kilometre; m.p.g. if

the speedometer

scale is represented

by the mile

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands