Fiat Punto 2004 Training Manual Download Page 465

Page: 465 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

9.3.1 System functions

Door locking/unlocking

The door locking system makes it possible to control the locks of the various doors from the

vehicle.

The door locks can be unlocked from the outside by putting the mechanic key into the latch

(driver’s door) and turning the same.

The vehicle’s doors cannot be locked if one or several doors are not fully closed. In this case,

a light signal informs you that the doors have not been locked.

In the event that the boot is open, the doors can be locked; yet, an acoustic signal will inform

you that an anomaly is found.

If the vehicle is locked from the outside, the door’s central locking/unlocking buttons will be

disabled and will be enabled again the next time the doors are unlocked.

Locking/unlocking actuation

The boot and door locking/unlocking can be actuated from the central board by means of

button C. Button

actuates the remote opening of the boot.

gb Fiat Grande Punto OK

464 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 465 / 533

Search results

Summary of Contents for Punto 2004

Reviews: