Fiat Punto 2004 Training Manual Download Page 108

Page: 108 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.6.3 Bosch CP1H high-pressure pump (90 HP)

Low pressure

inlet

KUEV valve

M-PROP

High pressure

outlet

Return

flow

Features

The 90 HP engine features a Bosch CP1H high-pressure pump, which is a step forward

compared with the CP1 pump. Now, the high-pressure pump makes a system pressure of up

to 1,600 bar available in the rail. This has been achieved by reinforced drive, modified valve

units and measures taken to increase the body sturdiness. To ensure a sufficient amount of

fuel, the high-pressure pump has been set to reach a total flow rate of 160 l/h.

The required flow rate is adjusted continuously by means of the M-PROP solenoid valve,

found on the high-pressure pump. This valve adjusts the fuel amount let into the rail to the

system requirement. Such flow rate adjustment makes it possible to reduce both the high-

pressure pump power absorption and the maximum fuel temperature. The feed pressure

required for the high-pressure pump is made available by an electrically-operated fuel feed

FIAT PUNTO

108 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands