Fiat Punto 2004 Training Manual Download Page 90

Page: 90 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.3.3 Engine oil lubricating circuit

Below is a representation of the engine lubricating system.

Plummet with filter strainer

Oil pump

Oil filter (with replacement cartridge)

Engine oil cooling water/oil heat exchanger

Nozzle (timing chain lubrication)

Engine oil pressure warning light switch

Turboblower lubrication pipes

Engine oil level dipstick

Engine oil level maintaining and scraper ring bulkhead

FIAT PUNTO

90 / 532

Timing chain cover

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 90 / 533

Search results

Summary of Contents for Punto 2004

Reviews: