Fiat Punto 2004 Training Manual Download Page 102

Page: 102 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

High pressure circuit

It is made up of the following items:

- pressure pump: CP1 (75 HP), CP1H (90 HP)

- single fuel manifold pipe with built-in pressure regulator and pressure sensor

- electric injectors CR1MI2.2

- connecting pipes.

High pressure line

FIAT PUNTO

102 / 532

Injectors (75 HP & 90 HP) = CR1MI2.2

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 102 / 533

Search results

Summary of Contents for Punto 2004

Reviews: