Fiat Punto 2004 Training Manual Download Page 269

Page: 269 / 533

8-VALVE 1.4

ENGINE

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

4.4.8 A/C linear sensor

Description

The A/C linear sensor checks correct system operation by taking over the task carried out by

the quadrinary pressure switch. The sensor continuously analyzes the air-conditioning system

circuit pressure and provides the engine control unit with real-time data of pressure variations,

thus making the actuation threshold management more flexible.

Position on the vehicle

1: A/C linear pressure sensor (placed on the high-pressure duct)

gb Fiat Grande Punto OK

269 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands