Fiat Punto 2004 Training Manual Download Page 488

Page: 488 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Bulb replacement:

act to tabs

to release the transparent glasses from the bumper, then

replace the bulbs by taking the bulb holder off the transparent glass.

Functions

The diagnosis is carried out by the trip computer, with the actuation control ON, as follows:

Side Anomaly

recognition

Front

Failure to one bulb

Failure to at least two bulbs

Rear

When a bulb anomaly is found, the trip computer signals (upon key-ON) the dimmer failure

indication.

Headlamp trim control:

it operates with the starting key turned to

“MAR”

and the low-beam

headlights ON.

The vehicle slopes backwards when it is loaded, thus causing the light beam to be raised. In

this case, the headlamps shall be orientated correctly again.

The trim can be controlled by pressing the buttons indicated by the arrows and located on the

control mask.

The instrument board display provides a visual indication of the control positions:

position

: one or two persons sitting on the front seats;

position

: five persons travelling on the vehicle;

position

: five persons travelling on the vehicle and luggage compartment loaded;

position

: driver plus maximum permitted load stored in the luggage compartment.

gb Fiat Grande Punto OK

487 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands