Fiat Punto 2004 Training Manual Download Page 452

Page: 452 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Functional diagram

S1-S2-S3-S4

Ultrasound sensors 1-4

Electric wire connection

Towing hook available

Electric wire connection

Output signals (see PAM)

B-CAN line

F404

Reverse gear actuation status

B-CAN line

F192

External temperature acquisition

B-CAN line

VF458

Buzzer actuation

Internal connection

F020

Vehicle speed/correct operation

B-CAN line

Failure warning light

Internal connection

System actuation and deactivation

When the vehicle is started (ignition key turned to “MAR”), a self-diagnosis test is carried out

by the control unit and the sensors: the system will be actuated when the reverse gear is

engaged, and will be deactivated when the reverse gear is disengaged.

gb Fiat Grande Punto OK

451 / 532

The acoustic signal emitted by the system warns the driver that the vehicle is drawing near an

obstacle. It consists of pulse sound signals: the signal duration is constant, whereas the pause

between the signals is directly proportional to the obstacle distance: pulses in a quick

sequence indicate the presence of a very near object.

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands