Fiat Punto 2004 Training Manual Download Page 156

Page: 156 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.10.12

Preheating spark plug check

During the phases below:

- starting phase,

- post-starting phase,

- the control unit manages timed operation of the spark plug preheating control unit (BITRON)

depending on the engine temperature.

gb Fiat Grande Punto OK

156 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands