Fiat Punto 2004 Training Manual Download Page 151

Page: 151 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.10.7 Engine jerk prevent check

The control unit processes the signals from the various sensors (engine revs; vehicle speed;

engine temperature; accelerator pedal potentiometer; brake and clutch switches) and corrects

the amount of fuel to be injected in order to improve driveability by reducing the running jerks

through the opening time of electric injectors CR1MI2.2 and the amount control valve DRV2.

gb Fiat Grande Punto OK

151 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands