Fiat Punto 2004 Training Manual Download Page 352

Page: 352 / 533

BRAKES

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

gb Fiat Grande Punto OK

352 / 532

1. Pump ground

2. Pump +30

3. Solenoid valve +30

4. Solenoid valve ground

5. Front left ABS sensor signal

6. Rear left ABS sensor power

supply

7. N.C.

8. Rear right ABS sensor power

9. Front right ABS sensor

power supply

10. Front right ABS sensor signal

11. K line

12. N.C.

13. N.C.

14. C-CAN L1 in

15. C-CAN L1 out

16. Front left ABS sensor

power supply

17. Rear left ABS sensor signal

18. Body Computer node

19. Rear right ABS sensor signal

20. Brake lights

21. ASR button input

22. ASR button LED

23. VSO output

24. N.C.

25. C-CAN H1

ABS control unit pin-out

26. C-CAN H”

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Fiat Punto 2004, Training Manual, Page: 352 / 533

Search results

Summary of Contents for Punto 2004

Reviews: