manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Configuration Guide

WAN Settings

173

17.4

WAN Settings

Flowchart: Configuring the ISP Settings

Select one of the
default providers in
“NET Configuration:
WAN”.

“SYS Configuration: System:
Country” =  “German”?

Is your IP address
allocated by your
provider?

Your own ISP

T-Online

DSL

(PPPoE)

LAN

ISP cannot be configured.

HDLC

PPP

No

No

No

Provider-New: Provider,

Telephone Number,

User Name and Password

Domain Name Server

Mail input server and

mail output server

Maximum idle time

Activate the status and

select the provider

T-Online: Telephone number,

Access identification, T-Online

number, Co-user number

and Password

Select a provider

from the list

Dynamic

IP address

Network mask

Your own telephone

number

Max. connection time

per month

Maximum idle time

Filter list IN

Filter list OUT

Finished

Gateway

Yes

No

No

Yes

No

Yes

Configure T-Online in “NET Configu-
ration: WAN: Provider”. You will obtain
the access data when you register.

Enter your provider's
dial-in data.

Do you want to configure
a new Internet provider?

Specify the IP address of
the DNS in the Internet.

Specify a standard POP server
and a standard SMTP server.

Specify the maximum time of
inactivity after which the connection
to the ISP is cleared down.

Configure the ISP in “NET Configu-ration:
WAN: ProviderConnections: ISP”.

Enter the IP address and network mask
you wish to obtain from your provider.

Specify the gateway
for the Internet
connection.

Specify the maximum
connection time for one month.

Specify the maximum time of inactivity after
which the connection to the ISP is cleared down.

Select the filter lists. Filter lists are created
in “NET Configuration: Firewall”.

Yes

Yes

Yes

Yes

No

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Danfoss ECL Comfort 110 Mounting Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 8
Danfoss AFQM Operating Manual preview
AFQM
Brand: Danfoss Pages: 16
Yealink MTouch Plus Quick Start Manual preview
MTouch Plus
Brand: Yealink Pages: 52
Walkera G120EFI User Manual preview
G120EFI
Brand: Walkera Pages: 22
VIS-A-VIS Vitalinq Supplemental Instructions preview
Vitalinq
Brand: VIS-A-VIS Pages: 4
Polycom RealPresence Group 500 systems System Setup Sheet preview
RealPresence Group 500 systems
Brand: Polycom Pages: 2
J.R. Clancy SceneControl 100 Operating Instructions Manual preview
SceneControl 100
Brand: J.R. Clancy Pages: 13
Panasonic SC-HC37 Owner'S Manual preview
SC-HC37
Brand: Panasonic Pages: 20
Panasonic SC-HC302 Operating Instructions Manual preview
SC-HC302
Brand: Panasonic Pages: 20
Panasonic SC-HC297 Operating Instructions Manual preview
SC-HC297
Brand: Panasonic Pages: 20
Panasonic SC-HC212 Operating Instructions Manual preview
SC-HC212
Brand: Panasonic Pages: 116
Panasonic SC-HC38 Owner'S Manual preview
SC-HC38
Brand: Panasonic Pages: 20
AEG MC 4469 DAB+ Instruction Manual preview
MC 4469 DAB+
Brand: AEG Pages: 32
AEG SRP 4332 CD/MP3 Instruction Manual preview
SRP 4332 CD/MP3
Brand: AEG Pages: 66
AEG MC 4428 CD Instruction Manual preview
MC 4428 CD
Brand: AEG Pages: 66
AEG MC 4450 iP User Manual preview
MC 4450 iP
Brand: AEG Pages: 54
AEG SR 4379 CD Instruction Manual preview
SR 4379 CD
Brand: AEG Pages: 46
AEG MC 4461 BT Instruction Manual preview
MC 4461 BT
Brand: AEG Pages: 54

Brands by name

Popular brands

Load more brands