manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Configuring the PC Software

Browser for OpenCTI and OpenHotel

164

Requirements

To use the systray display, you must first install TAPI; see 

Setting up TAPI

 starting on 

page 160.

Please note:

The systray display requires a current version of TAPI. If you 
are using TAPI from an earlier version of the OpenCom 100, 
you must first install the newer version from the product CD.

Installing the systray display

1.

Call up the start mask of the product CD (see 

Configuring the PC Software

 on 

page 158).

2.

From the start mask, select 

Software

: 

Install Systray

. Follow the program 

instructions.

3.

Start the program with 

Start

: 

Run

 and the configuration dialogue is displayed. 

Select one of the entries displayed under 

Existing PBXs

. Enter your user name 

and password in the boxes under 

Log-on

. 

4.

If you activate the 

Autostart

 check box, you will see the systray display even 

after restarting your PC.

5.

Confirm the entries in the configuration dialogue with 

OK

 and the systray 

display logs on for the OpenCom 100.

6.

Right-click on the systray display in the Start bar. Select 

Configu-

ration

 to call up the configuration dialogue. Select 

Network Con-

nections

 or 

Trunk Lines

 to produce a status dialogue.

16.5

Browser for OpenCTI and OpenHotel

You can simplify the daily use of the 

OpenCTI

 and 

OpenHotel

 Web applications 

using the Web browser especially adapted for the OpenCom 100. Each time the 
workstation is restarted, this browser program can automatically start and log you 
in. This means that the applications are always operational and can be accessed 
using the icon in the information area of the task bar.

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Yealink CP935W Quick Start Manual preview
CP935W
Brand: Yealink Pages: 8
µ-Dimension COMPETITION ProZ4-80 Manual preview
COMPETITION ProZ4-80
Brand: µ-Dimension Pages: 7
ORTAL Heat Control System Installation And Operation Manual preview
Heat Control System
Brand: ORTAL Pages: 20
Grundfos MP 204 Instructions Manual preview
MP 204
Brand: Grundfos Pages: 23
J&M Corporation STAGE-4 ROKKER XXR Custom Installation Instructions preview
STAGE-4 ROKKER XXR Custom
Brand: J&M Corporation Pages: 5
SEW-Eurodrive IPOS plus Manual preview
IPOS plus
Brand: SEW-Eurodrive Pages: 384
TechniSat Car Radio Operating Instructions Manual preview
Car Radio
Brand: TechniSat Pages: 24
ETC Insight 2x User Manual preview
Insight 2x
Brand: ETC Pages: 386
Pioneer DEH-23UB Owner'S Manual preview
DEH-23UB
Brand: Pioneer Pages: 36
Pioneer AVH-P4150DVD Installation Manual preview
AVH-P4150DVD
Brand: Pioneer Pages: 44
Pioneer DEH-2350UB Owner'S Manual preview
DEH-2350UB
Brand: Pioneer Pages: 64
Sony PCS-1 - Video Conferencing Kit Specification Sheet preview
PCS-1 - Video Conferencing Kit
Brand: Sony Pages: 2
Sony Ipels PCS-G50 Brochure & Specs preview
Ipels PCS-G50
Brand: Sony Pages: 8
Sony Ipela PCS-XG80 Brochure preview
Ipela PCS-XG80
Brand: Sony Pages: 8
Sony IPELA PCSA-CXG80 Operation Instructions Manual preview
IPELA PCSA-CXG80
Brand: Sony Pages: 91
Sony PCS-3000 Operating Instructions Manual preview
PCS-3000
Brand: Sony Pages: 123
Sony PCS-1500 Operating Instructions Manual preview
PCS-1500
Brand: Sony Pages: 140
Sony PCS-5100 Operating Instructions Manual preview
PCS-5100
Brand: Sony Pages: 154

Brands by name

Popular brands

Load more brands