DETEWE OpenCom 130 User Manual Download Page 38 | Manualshive

Page: 38 / 204

background image

Installation

Available Ports

36

one COM port to connect to a PC to configure and transmit connection data,
designed as an RJ45 jack

■

One port to the LAN (10BaseT), designed as an RJ45 jack

■

One CompactFlash “base” to incorporate a type I or type II CompactFlash
memory card. These cards are necessary to operate the OpenVoice and Open-
Attendant program packages. Only use high speed memory cards which are
recommended by DeTeWe. Other memory cards or “Microdrive” type memory
cards may not be able to maintain the required access speed.

Tip:

For the stored voice announcements and a recording time of
one hour a memory card with 32 Mbyte is required.

■

One port jack to connect the plug-in power supply. Only use the original
OpenCom 131 plug-in power supply provided in the supply scope.

3.8.3 OpenCom 150

The listed interfaces and ports are located on the main module or on the con-
nection module of the OpenCom 150. Further interfaces and ports can be added
by installing additional interface cards (see

Installing Interface Cards

starting on

page 29).

■

One slot to incorporate a double doorstation equipment interface card. The
following ports can be used with such a card:

Four actor ports for connection to a door opener and the intercom of door-
station equipment. These are designed as pressure terminals (actor1 and
actor3 to activate door openers, actor2 and actor4 to activate doorstation
equipment)

Four sensor ports for connection to the bell keys of doorstation equipment,
designed as pressure terminals (sensor 1 to sensor 4)

■

One slot to incorporate a V.24 add-on card. The following port can be used with
the V.24 add-on card:

one COM port to connect to a PC to configure and transmit connection data,
designed as an RJ45 jack

«
...
36
37
38
39
40
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Neo Car Audio Pages: 19

Brand: Datavideo Pages: 17

Brand: LAIA Pages: 71

dmc1 Finish-Out

Brand: M&S Systems Pages: 8

Markoprint iJET

Brand: Weber Pages: 127

Brand: Lightspeed Pages: 31

SoundPoint IP 501 SIP 2.2

Brand: Polycom Pages: 29

Brand: GROM Audio Pages: 16

Brand: Powrmatic Pages: 36

Brand: iRobot Pages: 7

Brand: Panasonic Pages: 20

MERLIN LEGEND Release 2.0 Analog Multiline Telephone

Brand: AT&T Pages: 794

Brand: Hyundai Pages: 88

Brand: Juniper Pages: 2

Brand: DS Pages: 7

Brand: Kitsound Pages: 10

Brand: Boss Audio Systems Pages: 6

Brand: AudioBahn Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands