DETEWE OpenCom 130 User Manual Download Page 60 | Manualshive

Page: 60 / 204

background image

Accessories and Adapters

U

pn

Adapter

58

4.

Accessories and Adapters

The OpenPhone 63 and OpenPhone 65 system telephones have one or two slots
on the rear for various adapters and other accessories. Further information on
installing and operating these add-ons can be found in the “OpenPhone 61, 63,
65” user guide under “Add-ons (with & without an Adapter)”.

In the following you will find technical details on the add-ons and a list of compa-
tible accessories.

4.1

U

pn

Adapter

The U

pn

adapter is an adapter with a U

pn

port for connecting another

OpenPhone 61, 63, 65 system telephone and a socket for an extra plug-in power
supply.

Weight: 70 g
Dimensions: 73 x 60 x 30 mm
Power consumption: max. 195 mW
Cable length: max. 30 m

Please note:

The U

pn

adapter may be used only for connecting the system

terminals listed above. The U

pn

extension cable must not ex-

ceed 30 m in length and must not be used outdoors.

Note:

An extra plug-in power supply is required to operate

combinations of equipment with a power consumption that
exceeds the power output of the U

pn

ports.

4.2

a/b Adapter

You can use an a/b adapter to connect analogue terminals to the OpenPhone 63
and OpenPhone 65 system telephones.

Connecting an a/b adapter will result in exceeding the feed performance of the
U

pn

port, regardless of the range. Therefore a plug-in power supply must be additi-

onally connected to the a/b adapter.

«
...
58
59
60
61
62
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Handicare Pages: 56

AUTOPULSE IQ-318

Brand: Notifier Pages: 62

Brand: Hyundai Pages: 26

Brand: ENTRYPASS Pages: 27

Brand: LSS Pages: 14

Brand: W. A. Production Pages: 5

Brand: Toa Pages: 12

Brand: Gemini Pages: 7

PELTOR ComTac 7

Brand: 3M Pages: 41

GIOTTO 30-50 BT

Brand: BFT Pages: 21

DOCKCONTROLLER DC-200

Brand: Motorola Pages: 16

Brand: HP Pages: 174

Brand: Bosch Pages: 252

Brand: JVC Pages: 2

Brand: JVC Pages: 16

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brand: JVC Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands