DETEWE OpenCom 130 User Manual Download Page 82 | Manualshive

Page: 82 / 204

background image

Configuration

Configuring the OpenCom 100

80

You can find further information in the chapter

PC Offline Configuration

starting on

page 158.

7.2.7 Remote Configuration

The OpenCom 100 configuration can also be altered or updated remotely by a cus-
tomer service centre or authorised dealer. This requires activation of internal RAS
access in the OpenCom 100 for the customer service centre/authorised dealer.

Note:

If one or more MSNs are entered on the

PBX Configuration

:

System

:

Remote service

menu page in

the Configurator and the

Status

option is activated, remote

configuration access is then activated when a data call from
one of the entered MSNs is registered.

The customer service centre/authorised dealer can then log into the
OpenCom 100 as an administrator:

■

User name: “Administrator”

■

Password: [administrator password]

Note:

If you do not wish to let the customer service centre/

authorised dealer know the administrator password, you can
define a temporary password for remote configuration with
at least five digits.

Use the following code digit procedure on a standard terminal or a system tele-
phone to activate internal remote maintenance access for the service centre/
authorised dealer:

Remote configuration on (log-on with administrator password)

H

*

1

9

*

Z

(system PIN)

#

Remote configuration on (log-on with temporary password)

H

*

1

9

*

Z

(system PIN)

*

Z

(temporary password)

#

Remote configuration off

H

#

1

9

#

«
...
80
81
82
83
84
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Samsung Pages: 22

Brand: Garmin Pages: 10

Brand: HandyTrac Pages: 14

MME239 - Micro DVD Home Theater System

Brand: Magnavox Pages: 41

Brand: Waterway Pages: 8

SB3.0-1SP-US-40

Brand: SMA Pages: 17

Soundgear Series

Brand: JBL Pages: 73

Brand: Polycom Pages: 2

Brand: Contec Pages: 15

Brand: Interroll Pages: 54

ConferenceSHOT AV

Brand: VADDIO Pages: 34

PNOZ m ES CC-Link

Brand: Pilz Pages: 24

e-Sense Actilume

Brand: Fagerhult Pages: 9

Brand: Audiovox Pages: 15

Brand: Champion Pages: 46

Brand: babala Pages: 30

Brand: Curtis Pages: 7

Brand: D-Link Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands