DETEWE OpenCom 130 User Manual Download Page 31 | Manualshive

Page: 31 / 204

background image

Installation

Installing Interface Cards

29

3.7

Installing Interface Cards

The expansion module and the basic module of the OpenCom 130 resp. the main
module of the OpenCom 150 can be expanded using interface cards. The main
module of the OpenCom 131 is quipped with one large and two small slots for
installing interface cards.

Please note:

Turn off the OpenCom 100. Unplug both the plug-in power
supply and (for an OpenCom 130/150) the main supply from
the socket. You must not install or uninstall interface cards
while the OpenCom 100 is turned on.

3.7.1 V.24 and Doorstation Equipment Slots

OpenCom 130: V.24 and doorstation equipment slots

OpenCom 131: V.24 and doorstation equipment slots

Doorstation
equipment

V.24

Doorstation
equipment

V.24

«
...
29
30
31
32
33
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Clatronic Pages: 38

Brand: Jensen Marine Pages: 18

Brand: V-ZUG Pages: 24

Brand: Polycom Pages: 4

Brand: Grace Digital Pages: 1

Brand: GAS Pages: 2

Brand: Waversasystems Pages: 24

Stealthbox SB-HY-VELOSTR/10TW3

Brand: JL Audio Pages: 7

Brand: Adcom Pages: 16

Brand: Philips Pages: 94

Brand: Philips Pages: 2

Brand: Philips Pages: 31

SoundStation 2W

Brand: Polycom Pages: 46

Brand: Sony Pages: 36

JumboTron JTC-C200

Brand: Sony Pages: 50

Brand: Sony Pages: 24

Brand: Sony Pages: 24

Brand: Sony Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands