DETEWE OpenCom 130 User Manual Download Page 20 | Manualshive

Page: 20 / 204

background image

Factory Settings on Delivery

Authorisations

18

The following terminal functions are factory preset to the “Administrators” group:

■

External line access: international numbers can be dialled from all configured
telephones. External lines must be seized by entering a prefixed code.

■

Least cost routing is not active. As soon as LCR is configured, users can make
calls via individually selected call-by-call providers.

■

“VIP call” is activated.

■

Announcements to system telephones are possible.

■

Baby calls can be configured.

■

If a call key is configured for a user on more than one terminal, he can program
this key for more than one outgoing call, i.e. he can use his various terminals to
make parallel calls from this telephone number.

■

“Pick-up” and “Pick-up selective” of calls from other telephones are activated.
Pick-up protection is deactivated.

■

“Call removal” is deactivated.

■

Callback (on busy) can be activated.

■

If more than one terminal is configured for a user under the same number, they
can suppress the signalling of calls on the parallel terminals.

■

Function “Reaction: Connection will be disconnected” is deactivated as callers
trying to reach a terminal that cannot be reached or is busy will hear a busy
signal.

■

The “call queue” function is deactivated.

■

Call forwarding to internal or external numbers can be activated. Call for-
warding after delay is executed after 20 seconds. Door calls and MSN groups
can be forwarded. Call forwarding for other users and call forwarding by other
users are deactivated.

■

It is possible to transfer an external call to an external subscriber.

■

Three-party conferences can be set up.

«
...
18
19
20
21
22
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: CAME Pages: 32

Brand: JETI model Pages: 64

Brand: auna multimedia Pages: 26

Brand: aija audio Pages: 4

Brand: Tokai Pages: 42

Brand: Blaupunkt Pages: 13

Brand: TechniSat Pages: 24

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 7

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 86

DEH-P2550 XN/ES

Brand: Pioneer Pages: 59

Brand: Pioneer Pages: 61

Brand: Pioneer Pages: 80

Brand: Pioneer Pages: 74

Brand: Pioneer Pages: 84

Brand: Pioneer Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands