DETEWE OpenCom 130 User Manual Download Page 63

Page: 63 / 204

Accessories and Adapters

Device Combinations

4.5

Device Combinations

You can use the following power values to calculate the power consumption of
combined equipment:

■

adapter: 195 mW

■

Audio adapter: 260 mW

■

a/b adapter: 160 mW
(must be combined with a plug-in power supply!)

■

OpenPhone 61: 1,000 mW

■

OpenPhone 63: 1,025 mW

■

OpenPhone 65: 1,140 mW

■

Up to three add-on keypads: 330 mW

These symbols are used in the following tables:

●

This combination is possible.

❍

Reduced tone ringing, open listening and hands-free talking volume possible.

Microphone:

Winfinity, 4511326 / H 282-18

Loudspeaker:

Siemens, L30460-X1278-X

Recording device:

No recommendation

The following devices are recommended:

Type

Manufacturer, Product Designation

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands