manualshive.com logo in svg

DETEWE OpenCom 130, User Manual

The DETEWE OpenCom 130 is a cutting-edge communication system that offers exceptional functionality and ease of use. To properly install and set up this device, you can easily access the Mounting And Commissioning Manual, available for free download on our website. This comprehensive manual will guide you through every step of the process, ensuring a seamless setup experience for your convenience.

Share
Download
background image

Configuration Guide

E-mail Access

177

17.8

E-mail Access

Flowchart: Configuring E-mail Access

Configuration of e-mail
access settings

Mail server

User accounts

Finished

Maximum number of e-mails

per user account

Enquiry interval

Start and end times:

Monday to Friday 1st starting time

Monday to Friday 1st ending time

Monday to Friday 2nd starting time

Monday to Friday 2nd ending time

Saturday 1st starting time

Saturday 1st ending time

Saturday 2nd starting time

Saturday 2nd ending time

Sunday 1st starting time

Sunday 1st ending time

Sunday 2nd starting time

Sunday 2nd ending time

NET Configuration: LAN

or WAN

User Manager: User Accounts

No

No

Yes

Yes

Do you have access to a mail server
in your network or in the Internet?

Do you have created mail account polls
in the “User Manager: User accounts”?

Specify the time intervals in which the
OpenCom is to poll all mail accounts
from the standard POP server.

Define the time windows in which the
OpenCom should check the mail accounts for
new messages in the time intervals that have
been set. You can define two time windows for
each working day (Monday to Friday), and two
each for Saturday and Sunday.

Configure your network/
Internet access.

Set up user accounts in
the User Manager.

Specify the maximum no. of e-mails per
user account that should be temporarily
stored by the OpenCom.

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

CAME G5000 Installation, Operation And Maintenance Manual preview
G5000
Brand: CAME Pages: 32
Union Instruments CWD2005 SPC Operating Instructions And Safety Notes preview
CWD2005 SPC
Brand: Union Instruments Pages: 63
Panasonic SC-PMX9DB Quick Manual preview
SC-PMX9DB
Brand: Panasonic Pages: 1
Panasonic SC-AKX18 Operating Instructions preview
SC-AKX18
Brand: Panasonic Pages: 2
Panasonic SC-PM02 Operating Instructions preview
SC-PM02
Brand: Panasonic Pages: 2
Panasonic SC-PMX90 Owner'S Manual preview
SC-PMX90
Brand: Panasonic Pages: 20
Panasonic SC-CH72 Operating Instructions Manual preview
SC-CH72
Brand: Panasonic Pages: 89
CLIMAVENETA CVM 2 Technical Manual preview
CVM 2
Brand: CLIMAVENETA Pages: 23
Bose Videobar VB1 Quick Start Manual preview
Videobar VB1
Brand: Bose Pages: 2
American Panel IC+ Manual preview
IC+
Brand: American Panel Pages: 18
TerraTec Aureon 7.1 FireWire Product Information preview
Aureon 7.1 FireWire
Brand: TerraTec Pages: 2
Daewoo AXL-125 Service Manual preview
AXL-125
Brand: Daewoo Pages: 22
Memsic DMU380SA Series User Manual preview
DMU380SA Series
Brand: Memsic Pages: 105
Digital Flash Memory MP3 On-Hold User Manual preview
MP3 On-Hold
Brand: Digital Flash Memory Pages: 10
Jensen MS3ARTL Owner'S Manual preview
MS3ARTL
Brand: Jensen Pages: 15
SMA DATA MANAGER L Operating Manual preview
DATA MANAGER L
Brand: SMA Pages: 64
Eding CNC CNC310 Hardware Manual preview
CNC310
Brand: Eding CNC Pages: 27
Raven SCS 660 Installation & Service Manual preview
SCS 660
Brand: Raven Pages: 60

Brands by name

Popular brands

Load more brands