DETEWE OpenCom 130 User Manual Download Page 185

Page: 185 / 204

Frequently Asked Questions

DECT

183

18.3

DECT

Note:

In the following explanations it is assumed that a U

interface card has been installed (in an OpenCom 130 or an
OpenCom 150).

The LED of the RFP 22/24 base station is flashing, but none of the DECT de-
vices is functioning.

Make sure the terminal setting for the corresponding U

port is set to

RFP 22/24

(

Configurator

PBX Configuration: Ports: U

menu).

If multiple

RFP 22/24

base stations are installed, the blinking LED indicates that

synchronisation is not finished.

The LED of the RFP 22/24 is continuously lit up, but one of the cordless DECT
devices is indicating “No connection”.

You have not registered this DECT device. Configure a port in the

Configurator

and start the enrolment procedure (

PBX Configuration: Devices: DECT Phones

menu).

Is it possible to increase the time for the enrolment procedure?

You must manually enter the IPEI of the DECT device in the

Configurator

. The

enrolment time is then increased to one hour (

PBX Configuration: Devices: DECT

Phones

menu).

Another manufacturer’s DECT device is not functioning.

Check whether the DECT device supports the DECT GAP standard. In the

Configu-

rator

, also make sure

GAP

is set for this DECT device (

PBX Configuration:

Devices: DECT Phones

menu).

The startup procedure of the RFP 22/24 take a long time? What is the reason?

This behaviour may indicate a problem with the reference clock. Refer also to

What

are some of the causes for problems when sending and/or receiving faxes?

starting on

page 182.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands