DETEWE OpenCom 130 User Manual Download Page 83 | Manualshive

Page: 83 / 204

background image

Configuration

Configuring the OpenCom 100

81

Activation is automatically cancelled 30 minutes after the last configuration
activity.

Note:

During remote configuration, the OpenCom 100 is

blocked for RAS access by any further users.

Please note:

The system PIN is preset to “0000” and it is absolutely impe-
rative that the system administrator changes it to prevent
undesirable remote maintenance.

Using remote configuration, all OpenCom 100 settings (with the exception of the
system PIN) can be edited or updated. New software versions of the OpenCom 100
and the software for the connected system terminals and base stations can also be
installed (see the

SYS Configuration: Firmware

menu in the

Configurator

).

For security reasons, settings in the

Configurator

,

Net Configuration

should only

be edited on site to avoid malfunctions or failures in the customer’s LAN (e.g. due
to IP address conflicts). Refer to the chapter entitled

Configuration Examples

starting on page 87, where interaction between the OpenCom 100 and a LAN is
explained.

Forced logoff of another user by the administrator

The configuration of the system can always only be edited by

one

user. Working on

the configuration in parallel is not possible. This ensures that no configuration
conflicts arise.

If the user “Administrator” logs in and another user with administration rights is
already logged in, then the administrator can forcibly log the other user off in
order to configure. This functionality, for example can be used, when configuring
remotely, when a user has forgotten to log out.

In order to forcibly log a user off:

1.

The “Administrator” user logs on with the administration password.

2.

They open the

Configurator

.

A message shows which user is currently configuring the system.

3.

The administrator clicks on the

Take over config rights

button.

The other user can make no further modifications of the configuration.

«
...
81
82
83
84
85
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: Skov Pages: 68

Brand: Intellitec Pages: 16

Brand: Aiwa Pages: 30

Brand: THOMSON Pages: 81

Brand: C.S.L. Pages: 27

Brand: SystemBase Pages: 22

DTM High Speed 7910

Brand: Becker Pages: 4

Brand: Vitek Pages: 28

Listening System PLS-900

Brand: Listen Pages: 2

Brand: Valcom Pages: 6

Brand: Anker Pages: 19

FCU-EXT-APP-CONTROL

Brand: Fasel Elektronik Pages: 2

Brand: Trevi Pages: 24

Brand: Teufel Pages: 16

Brand: Looperlative Pages: 29

Brand: RCA Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands