DETEWE OpenCom 130 User Manual Download Page 133 | Manualshive

Page: 133 / 204

background image

PBX Networking

Types of Point-to-Point Connections

131

Wiring of a direct connection

Note:

If you use an S

0

port on an interface card (pressure

terminal) and an S

0

port with an RJ45 jack for the direct con-

nection, make sure you make the necessary changes to the
port assignment (see

S0 Ports on Interface Cards

starting on

page 46).

12.2.2 Connection via an Active Transmission System

For distances exceeding the range of a direct connection, an active transmission
system can increase the range to up to 50 km. Normally the L1 master is the trans-
mission system for the two connected PBXs. For the protocol layers L2 and L3, one
PBX is normally the protocol master and the other PBX is the protocol slave.

Connection by an active transmission system

Note:

The active transmission system itself gets its L1 clock

either from the network operator or from a clock generator
connected by wire.

12.2.3 Connection via the Public Network

Point-to-point connections via the public network of a network operator can be
used for bridging distances beyond 50 km. Due to the long distance involved, for
technical reasons it is not possible to synchronise the L2 protocol. Consequently,
the public network is normally the protocol master for protocol layers L1 and L2.
One PBX is therefore the L3 master and the other PBX the L3 slave.

1 2 3 4 5 6 7 8

8 7 6 5 4 3 2 1

PBX 1, S

0

ext

PBX 2, S

0

ext

(RJ-45 socket)

PBX 1, S

2M

PBX 2, S

2M

(Pressure clamps)

Rx+ Rx-

Tx+

Tx-

Rx+ Rx-

Tx+

Tx-

PBX 1

L1 slave

L2 master
L3 master

PBX 2

L1 slave
L2 slave
L3 slave

Transmission

System

L1 master

«
...
131
132
133
134
135
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Saito Pages: 90

Brand: LENCO Pages: 27

Brand: Audipack Pages: 12

Brand: Quickie Pages: 108

Brand: Guardian Audio Pages: 4

Brand: Revo Pages: 15

Brand: Chrosziel Pages: 2

MERLIN LEGEND Release 6.0

Brand: Lucent Technologies Pages: 160

Brand: Foxtech Pages: 63

Brand: Aqua Control Pages: 16

Brand: Cisco Pages: 4

Brand: AMX Pages: 144

Brand: Sharp Pages: 4

Brand: Sharp Pages: 32

Brand: Sharp Pages: 48

Brand: Sharp Pages: 35

Brand: Sharp Pages: 48

Brand: Sharp Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands