DETEWE OpenCom 130 User Manual Download Page 62

Page: 62 / 204

Accessories and Adapters

Approved Devices / Approved Accessories

4.4

Approved Devices / Approved Accessories

Please note:

Only the following, recommended accessories may be con-
nected to the audio adapter. The cable to the door display
must not be run outdoors.

Electrical Data of Ports

Port

Connection Values

Microphone,
microphone of second handset,
headset microphone

Electret microphone
Typical sensitivity: 10 mV/Pa
Power feed: I < 300 µA at 1.5 V

Ear cap,
loudspeaker of second handset,
headset, headset loudspeaker

Typical impedance: 150 ± 30 ohms
Typical sensitivity: 94 dB/1 mW
(0 dB = 20 µPa)

Active speaker

Max. output voltage: 1 V

rms

at input impedance > 10 kohms

Recording device audio input

Typical input sensitivity: 0.24 mV
(microphone level)

Recording device start/stop
(relay contact 1)

Max. switching voltage:
50 VDC/29 V AC
Max. switching current: 1 ADC/0.7 A AC

Door display
(relay contact 2)

Max. switching voltage: 50 VDC/29 V

Max. switching current: 1 ADC/0.7 A AC

The following devices are recommended:

Type

Manufacturer, Product Designation

Headset:

GN-Netcom, Profile binaural
(1869-00-03)

GN-Netcom, Profile 3-in-1 (1866-00-04)

Headset adapter cable:

GN Netcom, QD cable (quick coupling),
smooth, Mod 4 (8800-00-01)

Second handset

Siemens, L30351-F600-A366

Handset

DeTeWe, OpenPhone 60

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands