DETEWE OpenCom 130 User Manual Download Page 176

Page: 176 / 204

Configuration Guide

RAS Settings

174

17.5

RAS Settings

Flowchart: Configuring the RAS Settings

LAN

Users

Status

Authorisation

Number of connections

Filter list IN

Filter list OUT

Add internal telephone

number to the incoming
call distribution scheme.

Finished

Yes

Configure users that
have RAS access rights.

Have you created users
with RAS access rights?

Select the filter lists. Filter
lists are created in “NET
Configuration: Firewall”

Specify how many simultaneous
connections are possible via this access.

Select from PAP,
CHAP and CLID.

Activate the RAS access.

Configure the network -
settings for the OpenCom.

Have you made the network
settings for the OpenCom ?

Configure the RAS access of the
OpenCom. “NET Configuration: RAS”

NET Configuration:

LAN

User Manager: Users

and User Groups

Telephone number

Specify the telephone number for which
the RAS access should be configured.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands