DETEWE OpenCom 130 User Manual Download | Manualshive

Page: 30 / 204

background image

Installation

Installing an Expansion Set

28

Installing the power supply for the expansion module

5.

Place the power supply to the right of the expansion module. Carefully press
the power supply into the mounting recess provided (shown in the diagram as
“1”). Move the power supply forwards until it snaps into place in all six pressure
terminals (“A”, “2”).

6.

Connect the power supply output (flat conductor cable) to the appropriate
jack of the expansion module. Insert the fully insulated connector of the mains
supply in the power supply connection provided.

7.

Establish an Ethernet connection between the LAN port of the basic module
and the LAN1 port of the expansion module (see also

Positions of the Ports

starting on page 37). To do this, use the short Ethernet connection cable from
the expansion set. The LAN0 port of the expansion module is intended for con-
nection to a corporate LAN. You can connect an existing Ethernet connection
cable to the LAN0 port of the expansion module.

You usually install at least one interface card on the expansion module. To do this,
read the instructions in the following section.

Please note:

Two power supplies are provided for the OpenCom 130 with
an expansion module. Always turn on the power supply of
the expansion module first and then plug in the plug-in po-
wer supply.

1.

2.

A

«
...
28
29
30
31
32
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Zenith Pages: 24

Brand: Samsung Pages: 2

Brand: Samsung Pages: 33

Brand: Yamaha Pages: 4

Brand: Hama Pages: 75

Brand: Aiwa Pages: 30

Brand: Goodmans Pages: 22

Brand: Madas Pages: 58

AeGIS 9100CR200

Brand: PACH & COMPANY Pages: 49

Brand: Maco Pages: 40

Brand: Prology Pages: 37

e-Sense Actilume

Brand: Fagerhult Pages: 9

Brand: CAME BPT Pages: 8

Brand: Revo Pages: 6

Brand: Roadstar Pages: 45

Brand: L.J. Wing Pages: 60

MAD-HIGHPOWER350CD

Brand: Madison Pages: 20

Brand: Panasonic Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands