DETEWE OpenCom 130 User Manual Download Page 189 | Manualshive

Page: 189 / 204

background image

Frequently Asked Questions

Internet

187

For information on the installation of software and on configuring Internet access,
refer to the “OpenPhone 26/27” user guide.

A SIP connection only passes unidirectional voice. What is the reason?

You did not use the OpenCom 100 as internet router or the STUN server of the SIP
provider is unavailable. You need to activate the SIP support at your internet
router, such as “SIP-ALG” or “Full Cone NAT” functions. You can also use the
OpenCom 100 for internet access. Correct the STUN setting in the

PBX Configu-

ration

:

SIP Provider

menu.

Is it possible to use Q.SIG-IP connections via an Internet access with dynamic
IP address?

Q.SIG-IP connections require a fixed IP assignment for technical and security
reasons. Therefore you need an Internet access with a fixed IP address. It is pos-
sible to tunnel a Q.SIG-IP connection through a VPN connection. A VPN con-
nection offers the possibility to determine the peer’s IP address with a DynDNS
service during connection setup. VPN and DynDNS can be realized with external
servers or routers.

«
...
187
188
189
190
191
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: iDance Pages: 25

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Cruisair SMX II

Brand: Taylor Made Environmental Pages: 36

Brand: Poly Pages: 28

Brand: Hama Pages: 45

Brand: babala Pages: 30

Brand: DriSteem Pages: 4

Brand: RCA Pages: 28

Brand: JVC Pages: 62

Stealthbox SB-D-DRNGO/10W0

Brand: JL Audio Pages: 3

Brand: Technika Pages: 16

EtherNet/IP E84DGFCGEJP

Brand: Lenze Pages: 149

Brand: Raven Pages: 104

Brand: Sharp Pages: 2

Brand: Sharp Pages: 28

Brand: Pioneer Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands