DETEWE OpenCom 130 User Manual Download Page 24

Page: 24 / 204

Installation

Scope of Delivery

Installation

3.1

Scope of Delivery

The delivery consists of:

■

One OpenCom 131 communications system (in a basic version) or
OpenCom 130 (in a basic version with a basic module) or OpenCom 150

■

One connection cable for the ISDN S

port

■

One set of mounting screws and wall plugs

■

One plug-in power supply (of the TR25240-E-01A13 type) to supply the basic
module

With the OpenCom 130 this power supply is dimensioned to operate the basic
module only. Installing the expansion module requires an additional power
supply.

■

One set of short user guides

■

One CD including the complete documentation and software

The OpenCom 130 expansion set consists of:

■

One expansion module

■

One AC adapter with a connection cable to supply the expansion module with
power

■

One mounting set with which to install the expansion module and the AC
adapter in the OpenCom 130 housing

■

One (short) Ethernet connection cable with which to connect the basic module
to the expansion module.

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands