DETEWE OpenCom 130 User Manual Download Page 174 | Manualshive

Page: 174 / 204

background image

Configuration Guide

LAN

172

17.3

LAN

Flowchart: Configuring Easy Access

Finished

Assign a name
to the OpenCom.

Specify the IP address of the OpenCom
under “Domain Name Server”. This is
transferred as the DNS server to the
client computers via DHCP.

LAN

Host name

DHCP

DNS

OpenCom

DHCP server

IP address

Network mask

PPP addresses

Finished

Yes

No

Yes

OpenCom as

DNS server

Register internal DNS

No

Yes

No

Do you have a DNS server
in your network?

Enter the Ethernet-IP confi-
guration for the OpenCom.

Activate the OpenCom
DHCP server.

Do you have a DHCP
server in your network?

Do you have a computer network?

Enter the address range
for the RAS accesses.

Gateway address

DHCP adresses

Domain name

Client computers are informed of this
gateway address via DHCP as a gateway.

Enter the address range of the
client computers in your network.

Enter the domain name. This name is
transferred to the client computers as
the domain via DHCP.

Specify the IP address of
your internal DNS server
under “Domain Name
Server”. This is transferred as
the DNS server to the client
computers via DHCP.

The OpenCom takes

the settings from
your DHCP server

Ask your network administrator for the
address range for the RAS accesses. For
this purpose, your administrator must
reserve an IP address range for the RAS
accesses.

«
...
172
173
174
175
176
...
»

Summary of Contents for OpenCom 130













































































































































































































Reviews:

No comments

Related manuals for OpenCom 130

Brand: Panasonic Pages: 3

Brand: HEIDENHAIN Pages: 64

Brand: Ziton Pages: 2

Brand: Intermatic Pages: 2

Brand: Jensen Pages: 4

Brand: Tibo Pages: 33

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: iWantit Pages: 32

Brand: Raven Pages: 47

Wireless music system for iPod

Brand: Brookstone Pages: 14

Brand: Foxtech Pages: 63

Brand: JVC Pages: 56

Brand: JVC Pages: 41

Brand: JVC Pages: 48

Brand: JVC Pages: 74

Brand: JVC Pages: 28

Brand: JVC Pages: 82

Brand: JVC Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands