DETEWE OpenCom 130 User Manual Download Page 61

Page: 61 / 204

Accessories and Adapters

Audio Adapter

Note:

Please use the plug-in power supply with the product

code 4505759. The plug-in power supply for use in the UK
has the product code 4510694.

Weight: 70g
Dimensions: 73 x 60 x 30 mm
Power consumption: max. 160 mW
Cable length: max. 3 m

4.3

Audio Adapter

The audio adapter is an adapter extension with four different ports for external
audio and signalling devices.

Weight: 70g
Dimensions: 73 x 60 x 30 mm
Power consumption: max. 260 mW (with relay active).

Audio Adapter Pin Assignment

Port

Used for

Socket

Assignment

Ear cap,
second handset,
headset,
active speaker or mi-
crophone

RJ-10
(4-pin
Western
socket)

1: microphone -

2: s

3: speaker -

4: micr

Recording device; re-
lay contact genera-
tes signal for starting
and stopping recor-
ding.

Stereo jack,
3.5 mm

1 (GND): recording
signal, relay contact 1

2 (peak): recording

3 (ring): relay contact 1

Not used on
OpenCom 100

Round power
socket
(4 mm)

Door display

RJ-11 or
RJ-12
(6-pin
Western so-
cket)

4, 5: relay contact 2

1, 2, 3, 6: NC

Summary of Contents for OpenCom 130













































































































































































































Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands

DETEWE OpenCom 130, User Manual

Search results

Summary of Contents for OpenCom 130

Reviews:

Related manuals for OpenCom 130

Brands by name

Popular brands